EpSignal

The EpSignal protocol is available on AppWebsocket connections to innovaphone PBX objects, if the object is enabled for the EpSignal api. It allows an application to insert itself into the signaling path of this device. All signaling messages to or from the device are then sent on this protocol. Signaling messages may be sent to the device or to the PBX.

This way the application may monitor any signaling done by the device, by forwarding the messages in both directions, or it may start signaling to the device or to the PBX on behalf of the device.

{
    "api": "EpSignal",
    "src": string,
    "mt": string,
}

api

To address this interface the value "EpSignal" has tp be used for the api property

src

The AppWebsocket src mechanism is supported on the interface. So a src property may be used

mt

The message type identifies the requested operation

• Attach - Attach to a device
• Signaling - Transfer of a signaling message

• AttachResult - Result of Attach
• Attached - A device was attached
• Detached - A device was attached
• Sync - Status of an existing call at Attach

{
    "api": "Api",
    "mt": "Attach",
    "hw": HardwareId
}

With this message the application attaches itself to a device addressed by hw

hw

Hardware Id used to address the device. This is the name also used for the VOIP registration of a device. Typically the MAC address of the device.

{
    "api": "EpSignal",
    "mt": "AttachResult",
    "err": Error,
    "stun": string,
    "turn": string,
    "turnUsr": string,
    "turnPwd": string,
    "prefixIntl":string,
    "prefixNtl":string,
    "prefixSubs":string,
    "area":string,
    "country":string,
    "maxIntern":integer,
    "tones":integer
}

Result of the Attach operation

err

If this property is present the Attach operation failed.

stun

A list of STUN servers as IP addresses or host names, seperated by semicolon

turn

A list of TURN servers as IP addresses or host names, seperated by semicolon

turnUsr

The user name to be used with TURN

turnPwd

The password to be used with TURN

prefixIntl

Prefix to be used to dial an international number from this node, including any trunk prefix

prefixNtl

Prefix to be used to dial a national number from this node, including any trunk prefix

prefixSubs

Prefix to be used to dial a subscriber number from this node, including any trunk prefix

area

Area code to be assumed for the user

country

Country code to be assumed for the user

maxIntern:integer

Maximum length of internal number

tones:integer

The tones scheme to be used for dialtones

{
    "api": "EpSignal",
    "mt": "Attached",
}

Indicates that the interface attached itself to a device. This may be delayed if no device was registered to the PBX at the time of the Attach. As soon as a device registers the interface attaches to it.

{
    "api": "EpSignal",
    "mt": "Detached",
}

Indicates that the interface detached itself from a device. This happens when the device unregisters from the PBX.

{
    "api": "EpSignal",
    "mt": "Sync",
    "call": CallId,
    "info": Info
}

Information about an existing call at at the time of the attach.

call

The call Id, which may be used for signaling messages related to this call.

info

More information about the call.

{
    "api": "EpSignal",
    "mt": "Signaling",
    "to": Direction,
    "call": CallId,
    "sig": Signal
}

This message is used to transfer Signaling messages coded according to the innovaphone Json signaling protocol.

to

Boolean property, which if present and true indicates that the message is in the direction to the endpoint. For messages received by the application this means the message is from the PBX. For messages sent by the application the message is sent toward the device.

call

Integer which identifies the call. To avoid conflicts a negativ number should be chosen for any call originating from the application. For messages received by the application the number received can be used when forwarding the message.

sig

The signaling message as innovaphone Signaling object.

For the signaling messages the standard innovaphone Json Signaling objects are used

More information about the call

{
    "channel": Channel,
    "in": Direction,
    "state": CallState,
    "remote": Remote
}

channel

Integer indicating the channel number. If this is a call without media, channel is 0. For VOIP endpoints a channel with media is always signaled with a channel of -1.

in

Boolean value indicating the direction of the call as seen from the device. A value of true means an incoming call, this means a call to the device.

state

A string indicating the state of the call. The following values are used:

null	Idle call, should not happen
setup	A call was initiated
setup-ack	A call was initiated, but more dialing information may be needed
call-proc	Dialing information is complete
alert	The called party alerted
connected	The call is connected
disconnected	The remote party disconnected the call
disconnecting	The local device disconnected the call
parked	The call was parked

remote

The remote party of the call

Information about the remote party of a call

{
    "num": Number,
    "sip": SipUri,
    "dn": DisplayName,
}

num

The Number as dialed to the remote party, or received as calling party

sip

SIP URI of the remote party. May be only the user part if on local domain

dn

Display name of the remote party, as received with a Name Identification facility